Guide
Separating restaurant premises and equipment scopes
Separate restaurant premises maintenance from cooking, gas, refrigeration, extraction and fire systems, and define where each contractor's scope ends.
By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For restaurant operators, owners and multi-site managers
A restaurant depends on two quite different sets of systems. One is the premises: air conditioning in the dining room and back of house, lighting and power, washrooms and sinks, drains, doors, ceilings and finishes. The other is the specialist equipment and safety systems: cooking equipment, gas, refrigeration and cold rooms, commercial kitchen extraction and grease ducts, and fire detection and suppression. Each set needs maintenance, but rarely from the same contractor.
When these scopes are mixed or left vague, faults fall between contractors, and an operator can believe something is covered when it is not. This guide explains how to separate the scopes clearly, define the points where they meet and set up a maintenance arrangement that fits around trading.
What premises maintenance typically covers
A restaurant premises maintenance arrangement, often set up as an annual maintenance contract (AMC), looks after the building systems and finishes. Following assessment, the agreed scope can include:
- AC equipment serving the dining area, offices, stores and back of house, for the units named in the contract.
- General electrical maintenance: lighting, switches, sockets and assessment of faults in the general electrical installation.
- Plumbing: taps, mixers, sinks, washrooms, visible pipework and agreed electric water heaters.
- Drainage: clearance of accessible drain sections in washrooms and agreed kitchen areas.
- Finishes and minor repairs: doors, locks, ceiling tiles, wall and floor tiles, painting and small carpentry repairs.
Planned work is often organised as planned preventive maintenance (PPM): scheduled visits to inspect and service named assets, with reactive repairs handled through an agreed callout and approval process.
What needs a separate specialist scope
The following should be listed separately, with their own named contractor or arrangement, and included in a premises contract only where the capability and delivery arrangements have been confirmed in writing:
| System | Why it is separate |
|---|---|
| Cooking equipment | Ranges, fryers, ovens, grills and combination ovens need manufacturer-specific knowledge and parts |
| Gas installations | Gas supply, pipework and gas appliance connections need appropriately qualified specialists |
| Refrigeration and cold rooms | Refrigeration systems, compressors and refrigerant handling are specialist work |
| Commercial kitchen extraction | Canopies, fans and extract ductwork are designed and serviced as a system |
| Grease ducts and canopy cleaning | Specialist cleaning with its own methods and records |
| Fire detection and suppression | Alarm, detection and kitchen suppression systems have their own maintenance and inspection arrangements |
| Grease traps | Emptying, cleaning and disposal need suitable equipment and disposal arrangements |
| Dishwashers, ice machines and beverage equipment | Usually serviced by the supplier or a specialist |
Requirements for fire systems, gas and food premises can involve authorities, landlords and mall management. Confirm with them and with your specialist contractors what applies to your premises, rather than relying on a general maintenance provider to tell you.
Define the points where scopes meet
Most disputes happen at the boundaries. A commercial fridge stops working: is it the refrigeration system, or the power supply to it? A dishwasher will not drain: is it the machine, or the drain beneath it? Defining the demarcation points in advance saves time when something goes wrong.
Common boundaries to write down include:
- Power to equipment. The premises electrical scope may cover the supply up to the isolator or socket; the equipment specialist covers the appliance from that point.
- Water and waste to equipment. The plumbing scope may cover pipework up to the isolation valve and the drain connection; the equipment specialist covers the machine.
- AC and kitchen extraction. Dining room AC is premises maintenance; the kitchen canopy and extract system belong to the extraction specialist, even where the two interact.
- Drains and grease traps. Clearance of accessible drain sections may be premises work under drainage cleaning; grease trap servicing and any jetting or tankering are separate.
- Ceilings and specialist systems. Repairing ceiling tiles is premises work, but anything involving fire detection devices, sprinklers or extraction above the ceiling needs the relevant specialist.
Record these boundaries in each contract and in your own contractor register.
Build a contractor register
A contractor register is a simple list showing each system, who maintains it, the contract reference, the visit schedule and how to report a fault. Keep it with your premises records and make sure shift managers know where to find it.
Useful columns include: system or asset, location, contractor, contact route, scope boundary, planned visit frequency, last visit and next visit due. When a fault occurs, the manager on duty can see immediately who to call, and you avoid the situation where a premises technician attends a fault that belongs to the refrigeration contractor.
Working around trading hours
Restaurant maintenance has to fit around service. When planning a premises arrangement, agree:
- Preferred visit windows, such as before opening or between services.
- Which tasks can be done during trading, and which must be done when closed.
- How noisy, dusty or disruptive work will be scheduled.
- How food areas, stock and equipment will be protected during work.
- Coordination with pest control, cleaning and specialist contractors so visits do not clash.
- Building or mall management rules on contractor access, permits and working hours.
The restaurant premises care approach shows how these elements can be organised in practice.
Questions to ask in a restaurant premises quotation
- Which assets and areas are covered? Ask for an asset list.
- Which specialist systems are excluded, and are any included through named specialist arrangements?
- Where are the demarcation points for power, water and drainage to equipment?
- How many planned visits are included, and what is done at each?
- How are reactive callouts handled, and what hours apply?
- How are spare parts, consumables and repairs priced and approved?
- What records are provided after each visit?
- How are visits scheduled around trading hours?
Next step
Use the restaurant premises maintenance checklist to list your premises assets and specialist systems side by side, with a named owner for each. Then share the list through the restaurant AMC service page so a premises scope can be assessed and quoted with clear boundaries.