Large-format porcelain floor tiles being laid with spacers

Renovation and finishes

Tile installation

Installation and replacement of floor and wall tiles for homeowners and refurbishment customers, covering substrate assessment, layout, laying, grouting and finishing at edges and junctions.

Overview

What tile installation covers

Tiling is unforgiving of shortcuts. An uneven substrate shows through as lippage between tiles, a poor layout leaves thin slivers at doorways, and the wrong adhesive or grout for the area can crack or stain. Classic Apex tile installation begins with checking the surface underneath and planning the layout, so the finished floor or wall looks deliberate and suits the way the space is used.

The tile itself needs to suit the area. Large-format porcelain behaves differently from small ceramic wall tiles, and wet areas need appropriate slip resistance and attention to falls. Where tiles are being replaced, removal of the old finish may reveal substrate damage. Waterproofing and screed renewal are not part of tiling by default; they are included only when specified, so the quote makes clear what lies beneath your new tiles.

Suitable for homeowners and refurbishment customers.

When it helps

What are you noticing?

Choose the closest description to see what it usually means for the request. This is guidance, not a diagnosis.

Damaged tiles

Cracked, chipped or loose tiles on floors or walls. Local replacement depends on matching tiles being available; otherwise a wider area, such as a full room, may need re-tiling.

Request a quotation for this

New finishes

Replacing dated floor or wall tiles in living areas, kitchens or corridors with a new style, size or layout that suits how the space is used today.

Request a quotation for this

Wet area upgrade

Re-tiling a bathroom, shower area or kitchen splashback, where slip resistance, falls to the drain and the interfaces with waterproofing and drainage outlets all need careful attention.

Request a quotation for this

Scope

What the assessed scope can include

The final scope depends on the assessment and is written into your quotation.

  1. 01

    Substrate assessment

    The assessment can include checking the floor or wall for level, soundness, moisture and the condition of the existing finish before a quotation is prepared.

  2. 02

    Removal of existing tiles

    Where agreed, the work can include removing old tiles and adhesive back to a sound base, with debris removal stated in the quote.

  3. 03

    Layout planning

    Planning can include setting out the tile layout to centre patterns, minimise small cuts and align with doorways, fixtures and features.

  4. 04

    Laying and cutting

    Installation can include fixing tiles with adhesive suited to the tile and substrate, cutting around fixtures and maintaining consistent joints.

  5. 05

    Grouting

    The scope can include grouting with the agreed grout type and colour, then cleaning residue and haze from the tile surface.

  6. 06

    Edges and junctions

    Finishing can include edge trims, movement joints, silicone at junctions with fixtures and transitions to adjacent floor finishes at doorways.

Price factors

What changes the quotation

Classic Apex does not publish fixed prices for this service. Each quotation is based on the actual work, separating labour, materials, access equipment, disposal and applicable taxes.

Area
Measured floor and wall areas set the main quantities of labour, adhesive, grout and tiles.
Tile size and type
Large-format, mosaic or natural stone tiles take longer to lay and cut than standard ceramics.
Wet or dry zone
Wet areas need more care with falls and interfaces, and possibly waterproofing if it is specified.
Supply
Whether you supply tiles or Classic Apex supplies them, with a wastage allowance, changes the quote.
Removal
Removing existing tiles and preparing the substrate beneath adds time, labour, noise and debris handling.
Layout complexity
Diagonal, herringbone or patterned layouts need more cutting and careful setting out than straight-lay installations.

Key specification choices

Tile selection
Type, size, finish and slip characteristics suited to the intended area, confirmed before ordering.
Adhesive and grout
Products chosen for the tile, substrate and area, including suitability for wet zones.
Layout
Pattern, starting point and joint width agreed in advance, with a sketch for complex layouts.

Process

How the work is organised

Tiling programmes depend on area, tile type, removal of existing finishes, substrate preparation and adhesive and grout setting times. Large-format tiles and complex layouts take longer. If screed or waterproofing is included, curing times add to the programme. Tile availability and delivery times also matter.

  1. Assessment

    Areas are measured and the substrate checked for level, soundness and moisture. Wet areas are assessed for falls and waterproofing interfaces, and the availability of matching tiles is discussed for any repair work.

  2. Quotation

    The quote states the area, tile supply, removal, preparation, layout, adhesive and grout, edge details and whether any waterproofing or screed work is included, so the specification beneath the tiles is clear.

  3. Work

    Adjacent areas are protected, old tiles are removed if agreed, the substrate is prepared and tiles are laid to the agreed layout. Grout is applied once the adhesive has set sufficiently.

  4. Completion

    Tiles are cleaned, joints and edges are checked and silicone is applied at junctions. The area is tidied, and you are told when the floor can take normal foot traffic and when wet areas can be used.

A preferred visit time is a request. It becomes an appointment only once Classic Apex confirms it.

Preparation

How to prepare

  • Measure the floor and wall areas to be tiled.
  • Choose tile size, style and finish, or share samples.
  • Say whether the area is wet, such as a shower, or dry.
  • Confirm whether existing tiles need removing.
  • Decide whether you will supply tiles and order extra for wastage.
  • Keep any spare tiles from the original installation for matching repairs.

Free checklist

Tile quantity and scope checklist

Use this checklist to estimate tile quantities and define your tiling scope before asking for a quote.

Tick what applies and add notes. Nothing is sent anywhere until you choose to request a quotation.

Go further with the flooring quantity

FAQs

Tile installation: common questions

Ask about your property
Can you replace just one cracked tile?

Often yes, if a matching tile is available. The damaged tile is carefully removed, the substrate beneath is checked and a replacement is fitted and grouted. If no match can be found, you may need to consider re-tiling a larger area so the finish stays consistent.

Is waterproofing included in bathroom tiling?

Not automatically. Waterproofing is a separate item that should be specified in the quote. If you are re-tiling a shower or other wet area, ask whether the existing waterproofing will be retained or renewed, and how that will be checked before the new tiles go down.

How much extra tile should I order?

A wastage allowance is usually added to cover cuts and breakages, with more needed for diagonal or patterned layouts. Keeping a box of spare tiles also helps with future repairs. The flooring quantity planner can help you estimate net and suggested order quantities.

Can new tiles be laid over old ones?

Sometimes, if the existing tiles are sound, well bonded and level, and the extra height still suits doors, thresholds and fixtures. The assessment checks this. Removal is usually recommended where old tiles are loose, hollow-sounding or uneven. An overlay can also hide problems in the substrate.

Enquire

Request a tile installation quotation

Share the location, the work you have in mind and a few photographs. We will advise on the next step and whether a visit is needed before quoting.

Telephone04 582 4141 Mobile+971 52 568 4874 Emailinfo@cafmglobal.com WhatsAppMessage us

Visit times and any assessment charge are confirmed before booking.

WhatsApp us