Plumbing and drainage
Water heater installation
Replacement and new installation of electric water heaters for homes, covering the choice of capacity, mounting, compatible plumbing and electrical connections, safety fittings and commissioning checks.
Scope and charges are agreed in writing before work starts.
SCOPE
Electric heater mounting compatible connections and checks.
BOUNDARY
Gas, solar and central hot water systems are separate.
Overview
What water heater installation covers
Electric water heaters in many homes sit out of sight, above a bathroom false ceiling, in a utility cupboard or on a wall bracket in the kitchen. When one starts leaking, takes too long to heat or trips its circuit, replacement often makes more sense than repair, especially on older units. Classic Apex water heater installation covers removing the old heater, mounting the new one and connecting it safely to the existing plumbing and electrical supply.
Choosing the replacement involves more than matching the old capacity. The available space, how the heater is mounted, how many outlets it serves and whether the electrical supply suits the new heater's rating all matter. The quotation states who supplies the heater, how the old one is disposed of and whether any pipework, wiring or ceiling access needs adjusting.
Suitable for homes with suitable electric water heaters.
When it helps
What are you noticing?
Choose the closest description to see what it usually means for the request. This is guidance, not a diagnosis.
Heater replacement
The existing heater leaks, makes noise, trips the circuit or no longer heats properly. An older unit with a failed element or tank may be better replaced than repaired.
Request a quotation for thisCapacity change
Household needs have changed and the current heater keeps running out of hot water, or a smaller unit would now suit a guest bathroom that is rarely used.
Request a quotation for thisNew installation
A new bathroom, kitchen or utility area needs its own heater, with the position, supports, plumbing and electrical connections planned from the start rather than added later.
Request a quotation for thisScope
What the assessed scope can include
The final scope depends on the assessment and is written into your quotation.
- 01
Site and access check
The assessment can include checking the heater location, the size of the ceiling access panel, the mounting surface and the condition of existing connections.
- 02
Removal of the old heater
The work can include draining, disconnecting and removing the existing heater safely, with disposal arrangements stated clearly in the quote.
- 03
Mounting
Installation can include fixing the new heater on suitable brackets or supports for its weight when full, in the agreed position.
- 04
Plumbing connections
The scope can include connecting the cold feed and hot outlet with compatible fittings, and fitting isolation valves where they are missing or faulty.
- 05
Safety fittings
Installation can include fitting or replacing the safety valve and its discharge arrangement, as the heater manufacturer requires for that model.
- 06
Electrical connection and commissioning
Work can include connecting to a suitable existing electrical supply, filling the heater, checking every joint for leaks and confirming that it heats correctly.
Price factors
What changes the quotation
Classic Apex does not publish fixed prices for this service. Each quotation is based on the actual work, separating labour, materials, access equipment, disposal and applicable taxes.
- Heater supply
- Whether Classic Apex supplies the heater or you provide it, and the model chosen, affects the total.
- Capacity and size
- Larger heaters are heavier, may need stronger supports and can be harder to manoeuvre into ceiling spaces.
- Ceiling access
- Small access panels may need enlarging to fit the new heater through, which adds work and reinstatement.
- Connection changes
- Reusing existing connections is simpler than adjusting pipework or wiring to suit a different heater model.
- Disposal
- Removing the old heater from site and disposing of it is quoted as a separate line item.
Key specification choices
- Capacity
- Chosen for household use, number of outlets served and available space, rather than simply copying the old unit.
- Mounting type
- Horizontal or vertical, wall-hung or ceiling-supported, matched to the location and the heater design.
- Safety valve and discharge
- Fitted or replaced as the manufacturer specifies, with discharge routed to a suitable point.
Process
How the work is organised
Scheduling depends on heater availability, whether the access panel needs enlarging and whether the existing connections suit the new model. Replacement in a ceiling void usually takes longer than a wall-mounted heater in a utility room. Building permit requirements and the need to keep at least one bathroom usable in an occupied home also influence planning.
Assessment
Photographs, capacity and location are reviewed first. A site visit then checks the ceiling access, mounting surface, connection type and electrical supply where these cannot be confirmed reliably from photographs alone.
Quotation
The quote states who supplies the heater, its capacity, removal and disposal of the old unit, mounting, safety fittings, connections and any access or wiring changes needed to complete the installation.
Work
Water and power are isolated, the old heater is drained and removed, and the new heater is mounted on suitable supports and connected, with its safety fittings installed as the manufacturer specifies.
Completion
The heater is filled and every joint checked for leaks before power is restored. Heating is confirmed at the outlets, the area is cleaned and you are shown the water and electrical isolation points.
A preferred visit time is a request. It becomes an appointment only once Classic Apex confirms it.
Preparation
How to prepare
- Note the existing heater capacity and model from its label, if visible.
- Photograph the heater and its connections, and the ceiling access panel if it is above a ceiling.
- Measure the access panel opening if the heater is in a ceiling void.
- Tell us whether you want Classic Apex to supply the heater or will supply it yourself.
- Switch off the heater at its isolator if it is leaking and it is safe to do so.
- Clear the area below the heater, including towels and cabinets.
Free checklist
Water heater replacement checklist
Use this checklist to gather the information needed for a water heater replacement quote.
Tick what applies and add notes. Nothing is sent anywhere until you choose to request a quotation.
Advice
Useful reading before you enquire
Planning electric water heater replacement
How to plan an electric water heater replacement: what to record, how to think about capacity and position, safety fittings and what the quotation states.
Read more ProblemPlanning replacement of an electric water heater
Signs an electric water heater may need replacing, safe checks to make first and the details that help Classic Apex quote a replacement clearly.
Read moreShould I repair or replace my water heater?
If the tank is leaking or corroded, replacement is usually needed, because the tank cannot be repaired reliably. If an element or thermostat has failed on a newer heater, a repair may be possible. The assessment can advise based on the age, condition and availability of parts.
What capacity heater do I need?
It depends on how many people use hot water, how many outlets the heater serves and the space available. Matching the old size is a starting point, but if the old heater ran out of hot water, a larger one may suit, provided it fits and the supports and electrical supply are suitable.
Do you install gas or solar water heaters?
Not as part of this service. Gas, solar and centralised hot water systems need a separate capability assessment and are not included automatically. This service covers suitable electric water heaters only, installed with compatible plumbing and electrical connections. If you have one of these systems, mention it when enquiring so the right route can be discussed.
Why does my heater need a safety valve?
Stored water heaters build pressure as the water heats. The safety valve and its discharge arrangement protect the tank if pressure rises too high. They are fitted as the manufacturer specifies and should never be blocked, capped or removed, even if they drip occasionally.
Related
Often arranged alongside
Plumbing installation
Compatible fixtures and agreed water and waste connections.
View serviceElectrical maintenance
Fault assessment and approved fitting or circuit repairs.
View servicePlumbing maintenance
Fixture fault assessment repairs and approved replacements.
View servicePart of plumbing and drainage. See the full service directory.
Enquire
Request a water heater installation quotation
Share the location, the work you have in mind and a few photographs. We will advise on the next step and whether a visit is needed before quoting.
Visit times and any assessment charge are confirmed before booking.