Plumbing and drainage
Plumbing maintenance
Assessment and repair of common plumbing faults for residents, landlords and business operators, including leaking taps, running toilets, visible pipe leaks and water pressure concerns.
Scope and charges are agreed in writing before work starts.
SCOPE
Fixture fault assessment repairs and approved replacements.
BOUNDARY
Hidden or shared system faults may need separate investigation.
Overview
What plumbing maintenance covers
Most plumbing problems announce themselves gradually: a tap that drips a little more each week, a cistern that keeps refilling at night, a damp patch under the kitchen sink. Left alone, they waste water and can damage cabinets, floors and ceilings below. Classic Apex plumbing maintenance focuses on finding out whether the problem is in the fixture itself or somewhere in the wider supply or drainage, then proposing a repair or replacement for approval.
Many faults can be fixed by replacing a washer, cartridge, flush valve or flexible hose. Others turn out to be a concealed leak, a shared riser issue or a pressure problem affecting the whole building. The assessment helps tell these apart, so you do not pay for a new mixer when the cause lies elsewhere, and so that building management is involved when the fault is beyond your property.
Suitable for residents landlords and business operators.
When it helps
What are you noticing?
Choose the closest description to see what it usually means for the request. This is guidance, not a diagnosis.
Leaking tap
A tap or mixer that drips from the spout, leaks around the handle or shows water at the base. Worn cartridges, washers and seals are common causes and can often be replaced.
Request a quotation for thisRunning toilet
A cistern that keeps running, refills on its own or takes a long time to stop. A faulty flush valve, fill valve or float adjustment is usually involved.
Request a quotation for thisVisible pipe leak
Water dripping from a joint under a sink, behind a toilet or at a water heater connection. Turn off the local isolation valve if safe, and photograph the leak.
Request a quotation for thisPressure concern
Weak flow from one tap, one bathroom or the whole property. The pattern helps show whether the cause is a blocked aerator, a valve or a wider supply issue.
Request a quotation for thisScope
What the assessed scope can include
The final scope depends on the assessment and is written into your quotation.
- 01
Fault assessment
The visit can include inspecting the affected fixture and nearby pipework, checking isolation valves and identifying whether the fault is local or wider.
- 02
Tap and mixer repair
Repairs can include replacing cartridges, washers, O-rings and aerators, or replacing the tap or mixer where repair is not practical.
- 03
Toilet cistern repair
Work can include adjusting or replacing flush valves, fill valves, seals and buttons on visible cisterns and on concealed cisterns that can be reached through the flush plate.
- 04
Hose and joint repair
The scope can include replacing flexible hoses, tightening or remaking leaking joints and replacing faulty isolation valves on visible pipework under sinks and behind fixtures.
- 05
Pressure checks
Assessment can include checking aerators, valves and fixtures for restriction, and testing flow at several outlets to identify the pattern.
- 06
Approved replacements
Where a fitting must be replaced, the work can include supplying and fitting an approved model, or fitting one you supply.
Price factors
What changes the quotation
Classic Apex does not publish fixed prices for this service. Each quotation is based on the actual work, separating labour, materials, access equipment, disposal and applicable taxes.
- Fixture type
- Concealed cisterns, thermostatic mixers and wall-mounted taps can take longer to repair than standard fittings.
- Parts needed
- Cartridges and valves vary by make, and some have to be ordered from the manufacturer or its agent.
- Location and access
- Fittings behind panels, under fixed cabinets or in tight spaces need extra time and care to reach.
- Number of faults
- Several issues fixed in one visit are more efficient than separate bookings for each one.
- Investigation needed
- Leaks of unknown origin or pressure problems may need more testing before a repair is quoted.
Key specification choices
- Repair or replace
- A worn cartridge or valve may be replaced on its own; an old or damaged fitting may be better replaced entirely.
- Replacement parts
- Parts are matched to the make and model where available, or a compatible alternative is agreed.
- Isolation valves
- Faulty or seized isolation valves are noted, since they make future repairs and emergencies easier to manage.
Process
How the work is organised
Most fixture repairs depend on part availability: common washers and hoses are easier to source than specific cartridges for branded mixers. Leaks needing investigation, building access requirements and coordination with building management for shared system issues can also affect scheduling.
Assessment
Your photographs and notes are reviewed before the visit. On site, the fixture and nearby pipework are inspected, isolation valves are checked and the fault is traced either to the fixture or to a wider system.
Quotation
You are told the likely cause and the proposed repair, with parts listed and priced. Hidden or shared faults are explained, together with the next steps and who else needs to be involved, such as building management.
Work
Water is isolated at the nearest working valve, the repair or replacement is carried out and joints are remade. The surrounding area, including cabinets and flooring, is protected from water throughout.
Completion
Water is restored and the fixture is checked for leaks, flow and correct operation. The area is dried and tidied, and any recommendations, such as replacing a seized valve, are explained before the visit ends.
A preferred visit time is a request. It becomes an appointment only once Classic Apex confirms it.
Preparation
How to prepare
- Photograph the leak or fixture and note when the issue started.
- Turn off the local isolation valve if safe to do so and place a container under drips.
- Note the make of the tap, mixer or cistern if visible.
- For pressure concerns, check whether it affects one tap, one room or the whole property.
- Empty the cabinet under the sink or around the affected area.
Free checklist
Plumbing fault information checklist
Collect these details before reporting a plumbing problem. They help separate fixture faults from wider issues.
Tick what applies and add notes. Nothing is sent anywhere until you choose to request a quotation.
Advice
Useful reading before you enquire
What information helps a plumbing enquiry
What to record and photograph when reporting a plumbing leak, the safe first steps and how to tell a fixture leak from a supply or drainage problem.
Read more ProblemLeaking taps and mixers
A dripping tap or a mixer leaking at its base wastes water and can damage cabinets. Safe checks, possible contributing factors and what to share when enquiring.
Read more ProblemReduced water pressure
Weak flow from taps or showers can come from a fitting, a pump or the wider supply. Safe checks, possible contributing factors and what helps an assessment.
Read more ProblemA toilet that keeps running
A toilet that keeps running or refilling can waste water and keep you awake. Safe checks, possible contributing factors and what to share before an assessment.
Read moreShould I repair or replace my leaking mixer?
If the mixer is in good condition and parts are available, replacing the cartridge or seals is often sensible. If it is corroded, damaged or parts are hard to find, replacement may make more sense. The assessment explains both options.
How do I find a hidden leak?
Signs include damp walls, stained ceilings below, a water meter moving with all taps off or a persistent musty smell. The assessment checks visible fittings first. Concealed leaks may need further investigation, and opening walls or floors would be discussed and quoted separately.
Why is my water pressure low?
Low pressure at one tap is often a blocked aerator or partly closed valve. Low pressure across the whole property may relate to the supply, tank, pump or building system. Telling us which outlets are affected helps narrow it down.
Can you fix a concealed cistern?
Many concealed cisterns can be reached through the flush plate opening, so valves and seals can usually be replaced without opening the wall. If the cistern body itself is leaking inside the wall, that may need further assessment and possibly tile removal, which would be quoted first.
Related
Often arranged alongside
Plumbing installation
Compatible fixtures and agreed water and waste connections.
View serviceDrainage cleaning
Assessment and clearance of agreed accessible drain sections.
View serviceWater heater installation
Electric heater mounting compatible connections and checks.
View servicePart of plumbing and drainage. See the full service directory.
Enquire
Request a plumbing maintenance quotation
Share the location, the work you have in mind and a few photographs. We will advise on the next step and whether a visit is needed before quoting.
Visit times and any assessment charge are confirmed before booking.