Guide
Planning electric water heater replacement
How to plan an electric water heater replacement: what to record, how to think about capacity and position, safety fittings and what the quotation states.
By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For homeowners, landlords and tenants with electric storage water heaters
Electric storage water heaters are common in villas and apartments, often tucked into ceiling voids, lofts, cupboards or bathroom walls. When one fails or starts to show its age, replacing it can look simple. In practice, the position, access, connections and choice of new heater all affect the work. This guide explains what to record, what to decide and what a clear quotation should include.
When replacement comes up
Replacement is usually discussed when a heater stops producing hot water, starts leaking, trips the electrical supply, shows rust staining or has needed repeated repairs. A fault does not always mean a new heater is required. Sometimes a component can be repaired. Ask for an explanation of what has failed and whether repair is a realistic option.
If water is leaking from or near the heater, switch it off at its isolator or at the distribution board if you can do so safely and the area is dry. Close the cold water supply valve to the heater if it is accessible and you know which one it is. Do not open the heater, remove covers or touch wiring. Keep people away from water near electrical fittings. Our page on water heater replacement signs covers safe checks in more detail.
Record the existing installation
Before requesting quotations, gather what you can from a safe position. You do not need to climb into ceiling voids; photographs from an open access panel or from the floor are usually enough to start.
| Detail | What to note |
|---|---|
| Location | Which bathroom, kitchen or ceiling area, and how it is reached |
| Orientation | Mounted vertically or horizontally |
| Capacity | The figure in litres on the rating plate, if visible |
| Make and model | From the label, if it can be read safely |
| Access | Size of the access panel or cupboard opening |
| Connections | Photographs of the pipework and any visible valves |
| Power | Location of the isolator switch, if there is one |
| Drainage | Whether there is a drip tray or a drain point below |
| Outlets served | Which bathrooms, showers and sinks take hot water from it |
Access is often the deciding factor. A new heater has to pass through the opening that the old one came out of, and a ceiling access panel may need to be enlarged if the replacement is a different shape. Find this out early.
Think about capacity and type
The new heater should suit how your hot water is used and the space available. It is tempting to replace like for like, which often makes sense, but it is worth pausing to check:
- How many people use the outlets served by this heater?
- Are showers taken at the same time, for example in the morning?
- Is a bath used regularly?
- Has the household grown or shrunk since the heater was fitted?
- Is the available space limiting what can be installed?
For example, in a three-bedroom villa where one heater serves two bathrooms used every morning by four people, the household might find that hot water runs out before everyone has showered. That is worth mentioning, because it may affect whether a different capacity, a second heater or a different arrangement is discussed. If the old heater coped well, say that too.
A larger heater is not automatically better if it does not fit the space or the access route, and a smaller one may not keep up with demand. Ask for the reasoning behind any recommended capacity and orientation, and make sure the selected product is designed for the position it will be fitted in.
Safety fittings, mounting and connections
A water heater installation is not only about the heater itself. The proposed work should include the safety fittings appropriate to the selected product, fitted in line with the manufacturer’s instructions. Ask which fittings are included and whether any existing ones will be reused or replaced.
Mounting matters too. The wall, frame or support must be suitable for the weight of a full heater, which is much heavier than an empty one. In ceiling installations, ask whether a drip tray or other drainage provision is appropriate for the position, so that any future leak has somewhere to go.
On the electrical side, the heater needs a suitable supply and means of isolation. Any changes beyond connecting to an existing suitable supply, such as a new circuit or alterations at the distribution board, should be assessed separately rather than assumed.
What the quotation should state
A clear quotation for water heater replacement should cover:
- Who supplies the heater, with make, model and capacity named
- Removal of the old heater and how it will be disposed of
- Installation, mounting and any supports or brackets
- Pipework adjustments, if the connections differ from the old heater
- Safety fittings included, and whether existing fittings are reused
- Electrical connection, and whether any wiring changes are needed
- Ceiling or cupboard access work, including enlarging panels and making good
- Commissioning checks, such as filling, checking for visible leaks and confirming hot water at the outlets
- Manufacturer warranty registration and any workmanship terms offered
- Exclusions and how unexpected findings will be quoted
If you rent the property, check with your landlord who approves and pays for the replacement before booking. In apartments, ask building management whether contractor access needs to be arranged, particularly if the old heater has to be carried through common areas.
What sits outside this scope
This guide covers individual electric storage water heaters. Centralised hot water systems serving a building, solar water heating and gas water heaters are different installations. They need a separate capability assessment and should not be assumed to fall under a standard electric heater replacement. If your hot water comes from a central system, start by speaking to building management.
Next step
Gather your photographs and notes in the homeowner project brief so the assessment has what it needs from the start. The water heater installation page explains how removal, installation and commissioning are scoped and quoted.