Guide

Tile considerations for wet areas

How to choose tiles for bathrooms, showers and other wet areas: slip resistance, absorption, size and falls, grout and sealant, and estimating quantities.

By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For homeowners and landlords planning bathroom, shower or laundry tiling

Bathrooms, showers, laundry rooms and kitchen splash zones put tiles under more pressure than most rooms. Floors get wet and slippery, water must run towards a drain and every joint and junction is a possible route for water. The tile you choose matters, but so does everything around and beneath it. This guide covers what to think about when selecting tiles for wet areas and what to ask before work is quoted.

Slip resistance on wet floors

A tile that looks good in a showroom can be slippery underfoot when wet. For floors in showers, bathrooms and around pools, slip resistance should be one of the first things you check.

Manufacturers may describe slip resistance using recognised test methods and classifications. These are not all the same, and a rating from one test cannot be directly compared with a rating from another. When choosing a floor tile for a wet area:

  • ask what slip resistance classification the tile carries and which test it refers to
  • ask whether that rating is suitable for a wet, barefoot area such as a shower floor
  • be cautious with highly polished finishes on wet floors, even if they suit dry areas
  • consider textured, matt or structured finishes for shower trays and wet zones

Remember that a tile’s slip resistance can change over time with wear, soap residue and cleaning products. Follow the manufacturer’s cleaning guidance.

Material and water absorption

Tiles absorb water to different degrees depending on their material and how they are made. In wet areas, lower absorption is generally preferred.

Material General characteristics Points to check
Porcelain Dense body, generally low water absorption Slip rating of the chosen finish; cutting needs suitable tools
Ceramic Often used for walls; floor suitability varies Whether it is rated for floors and wet areas
Natural stone Varied appearance, can be porous Sealing needs, sensitivity to some cleaning products, slip finish
Mosaic Small pieces on a mesh backing Grout volume and cleaning; good for shaping falls

Always check the manufacturer’s information to confirm that the tile is intended for the location you have in mind, such as a shower floor rather than a dry wall.

Think about cleaning as well. Deeply textured tiles can be safer underfoot but may hold soap residue and need more scrubbing, while light grout in a shower floor may show staining sooner than a mid-tone. Viewing a sample board with the proposed grout colour, ideally wet, gives a better idea of the finished look than a single dry tile.

Size, layout and falls to the drain

A wet-area floor is not flat. It should slope, or fall, towards the drain so that water does not pond. Tile size affects how well this can be achieved.

  • Large-format tiles have fewer joints but are rigid, which makes it harder to form falls in more than one direction. They can work well with a linear drain, where the floor falls in a single direction.
  • Smaller tiles and mosaics follow changes in slope more easily, which is why they are often used in shower trays with a central drain.
  • Layout should be planned around the drain position, the shower screen and the door, so that cuts are neat and small slivers are avoided at visible edges.

Discuss the drain type and position before choosing a tile size. Changing the drain or the falls may involve plumbing and screed work, which is a separate item in the quotation.

Waterproofing beneath the tiles

Tiles and grout are not a waterproof layer on their own. Water can pass through grout joints and hairline cracks, so wet areas depend on waterproofing beneath the tiles, carried up walls and around junctions as specified.

Before tiling starts, the scope should cover:

  • the waterproofing system to be used and where it will be applied
  • how it will be detailed around drains, pipe penetrations and junctions
  • testing of the waterproofing before tiles cover it, where appropriate
  • who is responsible for each stage if more than one trade is involved

A tile refresh that leaves the existing waterproofing in place should not be described as a waterproofing renewal. If you suspect the current waterproofing has failed, for example because of damp in a neighbouring room, it should be assessed first. Our guide to the bathroom waterproofing scope explains what to ask.

Grout, movement joints and sealant

Grout fills the joints between tiles. Cement-based grouts are common; epoxy and other resin grouts are also available and are often chosen for their resistance to staining, though they need more skill to apply. Ask which grout is proposed and why.

Junctions between walls and floors, around baths, shower trays and basins, and at changes of material usually need a flexible sealant rather than grout, because these joints move slightly. Silicone sealing and regrouting can refresh worn joints, but surface sealing is not a substitute for repairing failed waterproofing or a concealed leak.

Estimating quantities

You can estimate how many tiles you need with two formulas:

Floor area = length × width

Tiles needed = floor area × (1 + waste allowance) ÷ area of one tile

Worked example (bathroom floor):

  • Floor: 2.4 m × 1.8 m = 4.32 m²
  • Tile: 0.6 m × 0.6 m = 0.36 m²
  • Waste allowance: 10%, written as 0.10, for this example
  • Tiles = 4.32 × 1.10 ÷ 0.36 = 4.752 ÷ 0.36 = 13.2, rounded up to 14 tiles

For walls, use perimeter × tiled height, minus openings such as doors and windows. Waste allowances depend on the layout and the number of cuts; diagonal or patterned layouts usually need more. Tiles are sold in boxes, so round up to whole boxes. Keep a few spares from the same batch, because localised replacement later depends on finding a matching tile.

Next step

Work out your floor and wall areas and tile quantities with the flooring quantity planner, then share your measurements and preferred tiles when you enquire. The tile installation page explains how substrate preparation, waterproofing interfaces and finishing are scoped.

Enquire

Tell us what your property needs

Share the location, the work you have in mind and a few photographs. We will advise on the next step and whether a visit is needed before quoting.

Telephone04 582 4141 Mobile+971 52 568 4874 Emailinfo@cafmglobal.com WhatsAppMessage us

Visit times and any assessment charge are confirmed before booking.

WhatsApp us