Guide
Planning bathroom fixtures and connections
Plan bathroom fixtures around their connections: toilet, basin, shower, bath, water heater, fan and lighting, plus what changes when positions move.
By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For homeowners and landlords replacing bathroom fixtures or planning a renovation
Bathroom fixtures are usually chosen for how they look, but each one also has to connect to water, drainage and sometimes power, and has to be fixed to a wall or floor that can hold it. Planning the connections at the same time as the selection avoids buying a basin that does not suit the waste position, a shower that needs more pressure than the property provides, or a wall-hung toilet without a frame behind it.
This guide works through the common fixtures, what to record for each, and the questions to ask when fixtures are being installed or replaced.
Start with what stays where
The biggest planning decision is whether fixtures stay in their current positions. Replacing like for like in the same place usually means connecting to existing supply and waste points, with limited opening of walls or floors. Moving a toilet, shower or basin brings in new concealed pipework, possibly new drainage falls, and the making good of tiles and walls. That is not a reason to avoid a better layout, but it is a reason to decide early.
Toilets have the least flexibility because of the size of the waste connection and the falls it needs. In apartments, waste pipes often connect to shared stacks, and changes near those connections may need building management involvement.
Measure the space as well as the positions. Note the room width and length, the door width and which way it swings, the window position, the ceiling height and any boxed-in pipes. Check that each fixture leaves comfortable space in front of it and that the door will not hit the basin or toilet once everything is fitted. A quick sketch with these dimensions makes it much easier to check a new layout before anything is bought.
Fixture by fixture
| Fixture | What to record | Common questions |
|---|---|---|
| Toilet | Floor-mounted or wall-hung, waste outlet type, distance from wall to waste centre | Is a concealed cistern frame needed? Where is the access panel? |
| Basin and vanity | Wall-hung, pedestal, countertop or vanity unit, tap holes, waste and trap type | Does the wall need reinforcement? Does the waste height suit the unit? |
| Taps and mixers | Deck or wall mounted, single lever or separate, connection sizes | Are isolation valves fitted or planned? |
| Shower | Exposed or concealed valve, thermostatic or manual, overhead and handheld outlets | What pressure does the valve need? Where is the drain? |
| Bath | Size, freestanding or built-in, waste and overflow, panel type | How will the waste be accessed later? |
| Hand spray or bidet spray | Supply connection, hose length, valve position | Is there a nearby isolation point? |
| Water heater | Capacity, location, ceiling or wall mounting | Is there safe access for maintenance and replacement? |
| Extract fan | Wall, ceiling or window position, discharge route | Does the route lead to a suitable outlet? |
| Lighting and mirror | Ceiling lights, mirror lighting, switching position | Is the fitting suitable for its zone in a bathroom? |
Ask for the manufacturer’s installation sheet for each product. It sets out connection sizes, minimum and maximum pressures where relevant, fixing requirements and any space needed for maintenance.
Concealed items need early decisions
Some fixtures depend on parts that are built into walls or floors.
- Concealed shower valves sit inside the wall. The valve body must match the trim kit you choose, and it has to be set at the right depth for the finished wall.
- Wall-hung toilets need a frame and concealed cistern, with an access panel for servicing the flush mechanism.
- Wall-hung basins and vanities need suitable fixings or reinforcement in the wall.
- Linear drains need the floor falls planned around them.
- Built-in baths need access to the waste for future maintenance.
These parts are installed during first fix and tested before walls are closed. Changing your mind after that stage usually means opening finished surfaces. The guide to bathroom renovation work stages shows where these decisions sit in the sequence.
Water pressure and supply
Some shower valves, rain heads and fittings perform best within a particular pressure range set by the manufacturer. Before choosing, it helps to know how the property is supplied: from a mains supply, a roof or ground tank, or through a booster pump. If you already notice weak flow at some outlets, note which ones and when; the page on reduced water pressure explains what information helps. Pressure concerns that come from shared building systems need to be raised with building management.
Water heater capacity and position also matter if you are adding outlets or a larger shower. Gas, solar and central hot water systems are outside a standard electric water heater scope and need separate assessment.
Electrical items in the bathroom
Bathrooms have specific requirements for electrical fittings because of water and steam. Lighting, mirror lights, fans, heated towel rails and any sockets should be suitable for their position, and new circuits or supply changes need electrical assessment. The electrical installation service covers assessed connections for new fittings. Do not position or wire bathroom electrics yourself.
Questions to ask in the quotation
- Which fixtures are supplied, and which are customer supplied?
- If you supply fixtures, who checks them on delivery and before installation?
- Are isolation valves, flexible connectors, wastes and traps included?
- Does the scope include any new pipe routes, and is making good of tiles and walls included?
- How will supply pipework be tested before it is concealed?
- What checks are done at handover, such as flow, drainage and visible leak checks?
- How are access panels for concealed cisterns, baths and valves provided?
Next step
List your chosen fixtures, their model numbers and positions in the homeowner project brief so connections can be checked against the existing room. Then enquire through the plumbing installation service page to confirm compatibility and scope before you buy.