Guide
Planning repairs to uneven external paving
Plan repairs to uneven interlock paving: record where it has moved, consider possible causes, measure the area and know what a repair quote should cover.
By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For villa owners, landlords and community or building managers
Interlock paving is popular for driveways, paths and patios because individual pavers can be lifted and relaid. When an area becomes uneven, it is tempting to simply replace the pavers that look worst. Often, though, the visible movement is a symptom of a problem underneath: a base that has settled, bedding that has washed out, edges that have moved, or roots or pipes pushing up from below. A lasting repair starts by understanding which of these is happening.
This guide explains what to record, possible contributing factors to consider, how to measure the area, and what to ask in a repair quotation.
What to record before you enquire
Walk the paved area and note the problems in detail. Photographs taken from a low angle show unevenness much better than photographs from standing height.
- Sunken areas: where pavers have dropped below the surrounding surface.
- Lifted areas: where pavers are pushed up, often in a line or around a tree.
- Rocking pavers: pavers that move underfoot.
- Broken or cracked pavers, and whether they are in vehicle areas.
- Open or empty joints, where sand has been lost.
- Moving edges: kerbs or edge restraints that have shifted outwards.
- Pooling water: where water collects after irrigation, washing or rain, and how long it stays.
- Weeds growing through joints.
Note how each area is used. A path used on foot, a patio with furniture and a driveway used by vehicles place very different loads on the paving. Mark any trip hazards clearly until they are repaired.
Possible contributing factors
Without lifting the pavers, the cause cannot be confirmed, but these are common contributing factors to consider. They are not a diagnosis.
| What you see | Possible contributing factors |
|---|---|
| Sinking in wheel tracks | Base not built for the loads, or settled over time |
| Sinking near a gully or downpipe | Water washing out bedding or base material |
| Sinking along a pipe or cable route | Backfill settling after earlier excavation |
| Lifting in a line near trees | Root growth below the paving |
| Damp, sinking patch with no obvious source | Possible leak from irrigation or a buried pipe |
| Edges spreading outwards | Missing or failed edge restraint |
| Widespread small movements and open joints | Loss of joint sand, allowing pavers to move |
If water appears to be coming from below, or an area stays damp without irrigation, mention it. A leaking pipe or irrigation line under paving needs to be found and fixed before the paving is relaid, or the problem will return. The page on uneven external interlock paving has more on what to note.
Measuring the area
Measure each affected area as one or more rectangles and record the length and width in metres. Area is length multiplied by width; add the rectangles together for the total. If it is likely the repair will extend beyond the visibly damaged zone, which is common when the base needs correcting, measure a little wider and note that you have done so.
For ordering, add an allowance for cutting and breakages:
Order area = net area × (1 + waste allowance)
For example, two sunken areas of 3.0 m × 2.0 m and 1.5 m × 1.2 m give 6.0 + 1.8 = 7.8 m². With a 10% allowance, the order area would be 7.8 × 1.10 = 8.58 m². The right allowance depends on paver size, pattern and cutting, and should be confirmed by whoever quotes the work. If you need square feet, multiply square metres by 10.7639.
Edges and kerbs are measured in linear metres.
Matching pavers and appearance
Matching existing pavers is often the hardest part of a local repair. The same product may no longer be made, colours vary between batches, and older pavers fade and weather. Even an exact match will look newer for a while.
- Check whether you have spare pavers from the original installation.
- Photograph a paver next to a tape measure and note its shape, thickness if visible and colour.
- Consider whether lifted pavers can be cleaned and reused, with new pavers placed in less visible areas.
- Decide whether a slightly different but complementary paver is acceptable, or whether a larger area should be replaced for consistency.
Cleaning the surrounding paving can reduce the contrast between old and new areas. External pressure washing should use a method and pressure suited to the paving, and is best done once repairs are complete and joints have settled.
Levels, drainage and what lies beneath
A repair is a chance to correct levels. Paving next to a building should fall away from it so that water does not collect against walls or doorways. Gullies, channels and drainage points should sit correctly within the finished surface.
Before excavation, identify anything buried below the paving: irrigation lines, sprinkler heads, garden lighting cables, drainage pipes and service routes. Share drawings if you have them. In villa communities and shared developments, check with the community or building management whether approval is needed for works to driveways, paths or areas visible from the street, and whether there are rules on working hours and skip placement.
Questions to ask in the quotation
- Does the repair include lifting and correcting the base, or only relaying pavers?
- How deep will excavation go, and what base and bedding materials are proposed?
- How will levels and falls be set, especially near the building and drains?
- Are new pavers supplied, and how will matching be handled?
- Are edge restraints and kerbs included where they have moved?
- Is joint sand, compaction and final cleaning included?
- How is excavated material removed and disposed of?
- What happens if a leak, roots or buried services are found?
Next step
Record your measurements and allowance in the flooring quantity planner, which works the same way for external paving areas. Then share your photographs and measurements through the interlock works service page so the base, levels and drainage can be assessed before repair.