Guide

Planning additional sockets and fittings

How to plan extra sockets, switches and light fittings: positions, heights, connected load, cable routes, approvals and what the quotation should define.

By the Classic Apex team · Updated 22 October 2026 · About 5 minutes to read · For homeowners, landlords and occupiers planning electrical upgrades

Extension leads trailing across a room, a desk without power nearby or a kitchen worktop with one socket for four appliances: these are common reasons people want extra sockets and fittings. Adding them is often straightforward, but the result depends on planning. Positions need to suit how the room is used, the circuit must be suitable for what will be connected and the finish around new fittings needs to be considered. This guide explains how to prepare a clear brief.

Start with how each room is used

Before thinking about sockets, think about the room. Walk through it and picture where people sit, work, cook, charge devices and watch television. Note where furniture is now and where it will be after any changes.

For each room, list:

  • the furniture that fixes positions, such as beds, sofas, desks, wardrobes and kitchen units
  • the items that need power at each position, such as lamps, televisions, routers, chargers and appliances
  • where extension leads are currently used, because these show where power is missing
  • where you want light switches, including two-way switching for stairs or long rooms
  • any new light fittings, such as pendants, wall lights or under-cabinet lighting

It helps to mark positions on a photograph of each wall or on a simple floor plan. Note approximate heights too, such as above a worktop, beside a bed or behind a wall-mounted television.

Think a little ahead as well. If you may add a home office, a second television or an electric vehicle charger later, say so now. Planning spare capacity or a cable route at the same time is usually simpler than coming back to open finished walls. Equally, avoid positions that will end up hidden behind fixed furniture or appliances, unless that is intended, as with a socket for a built-in fridge.

Think about what will be connected

The number of sockets matters less than what they will be used for. A bedroom socket for a phone charger and a lamp is very different from a kitchen socket that will run a kettle, toaster and coffee machine.

Area Typical items Points to raise
Kitchen worktop Kettle, toaster, coffee machine, mixer Several high-demand items used at once
Built-in appliances Oven, hob, dishwasher, washing machine Whether dedicated circuits or connection points are needed
Home office Computer, screens, printer, router Number of outlets and position relative to the desk
Living room Television, audio, consoles, lamps Height behind a mounted screen, cable management
Bedrooms Lamps, chargers, fans Positions either side of the bed
External areas Lighting, garden equipment Suitability for outdoor exposure

Heavier loads, such as ovens, water heaters and some kitchen appliances, may need their own circuit. Any new circuit or work at the distribution board must be separately assessed, with load capacity checked against the existing system. It is not enough to add sockets to an existing circuit without checking whether it can support what will be connected.

Wet areas and special locations

Bathrooms, kitchens near sinks, laundry areas and external spaces need particular care. The positions and types of fittings allowed near water are controlled by the applicable wiring rules, and the assessment will confirm what is suitable for each location. Do not assume that a position used in another property will be acceptable in yours. If you would like a shaver point, a heated towel rail or lighting in a bathroom, mention it at the start so it can be planned properly.

Cable routes and the finish around new fittings

There are two broad ways to run new cables:

  • Concealed: cables are run inside walls or ceilings. This gives a cleaner result but involves cutting into surfaces and then making good, which may include plastering, painting or, in tiled areas, replacing tiles.
  • Surface run: cables are run in neat trunking or conduit on the surface. This is less disruptive and quicker to finish, but more visible.

The right choice depends on the room, the wall construction, the finish you want and whether other work is planned. If you are already repainting, retiling or installing gypsum ceilings, it often makes sense to coordinate the electrical work first, so that cable routes are in place before finishes are applied. Kitchen projects in particular benefit from this; our kitchen renovation checklist covers how to sequence electrical work with cabinets and tiling.

Ask the quotation to state clearly whether making good is included and to what standard, for example filled and ready for painting, or fully painted to match.

Approvals and permissions

Before alterations go ahead, check:

  • with building management, whether electrical alterations in your unit need approval, what contractor access arrangements apply and which hours work is permitted
  • with your landlord, if you rent, whether you may add fittings and who pays
  • with the relevant authority, through the assessment, whether any approvals or inspections apply to the planned work

The assessment should tell you if anything in your plan needs further approval or a different approach.

What the quotation should define

  1. Each new socket, switch and fitting, with its location
  2. The type and finish of each accessory, and who supplies it
  3. Whether cables are concealed or surface run in each area
  4. Whether any new circuits or distribution board work are included
  5. Making good, and the standard of finish
  6. Testing after installation
  7. Exclusions, such as decorating or tile replacement, if not included

For decorative lighting, dimming or smart controls, ask about product compatibility with your existing switches and wiring. The lighting and smart controls page covers those upgrades.

Next step

Mark your positions and list what will be connected in the homeowner project brief, then add photographs of each wall. The electrical installation page explains how routes, circuit suitability and load are checked before work is quoted.

Enquire

Tell us what your property needs

Share the location, the work you have in mind and a few photographs. We will advise on the next step and whether a visit is needed before quoting.

Telephone04 582 4141 Mobile+971 52 568 4874 Emailinfo@cafmglobal.com WhatsAppMessage us

Visit times and any assessment charge are confirmed before booking.

WhatsApp us